Board điều khiển SCR-P/N: FCOG61BP Hãng: ENERPRO

1078
4154

INO Measure Co., Ltd có khả năng tư vấn mua sắm, sử dụng, lắp đặt và cung cấp các thiết bị:  Đo lưu lượng,nhiệt độ, áp suất, mức, đo khoảng vị trí khoảng cách, đo lực và Momen, đo các đại lượng điện, thiết bị kiểm tra giám sát,thiết bị phân tích thử nghiệm,thiết bị hiệu chuẩn, điều khiển PLC, Giam sát truyền động, Linh kiện điện, Thiết bị đóng cắt và bảo vệ an toàn, Biến tần-Khởi động mềm, Động cơ hộp số, máy bơm, Van các loại  

 Nếu bạn có nhu cầu mua sắm hoặc cần sự hỗ trợ về kỹ thuật cho một thiết bị không được liệt kê ở đây, xin vui lòng liên hệ với chúng tôi;

Vui lòng liên hệ với chúng tôi– chúng tôi sẽ liên hệ lại với khách hàng bằng điện thoại hoặc email.

Lưu ý: Tham khảo ý kiến của nhân viên INO sẽ giúp bạn tiết kiệm được thời gian và chi phí khi cần mua sắm. ​​Với sự tư vấn của chúng tôi, bạn sẽ không gặp khó khăn khi tìm hiểu về đặc tính của sản phẩm cần mua.”

Thông tin sản phẩm:

The FCOG61BP firing board is based on the FCOG6100 three-phase, six-SCR firing board. It features an additional set of six gate outputs and a polarity transition circuit, allowing users to easily realize four-quadrant rectifier and series-reversing AC controller circuit topologies.


KEY FEATURES

  • Industry Standard Digital LSI-Based Design
  • Fully Connectorized
  • Soft-Start and Soft-Stop Circuitry
  • Multiple Configurations Avaliable
  • Polarity transition command with configurable dead time
  • Designed for Panel Mounting
  • Complete SCR Assemblies Available

The FCOG61BP includes the following features:

  • Analog Delay Angle Command Signal (SIG HI): Users may choose a variety of DC control signal ranges including 0-5 V, 4-20 mA, or custom ranges.
  • Soft-Start and Soft-Stop: Upon soft-start, SCR firing is enabled and the delay angle command ramps from the maximum value to the setpoint value determined by the SIG HI command signal. Upon soft-stop, the delay angle ramps from the setpoint value to the maximum value after which SCR firing is inhibited.
  • Instant Enable and Inhibit: A contact closure (relay, switch, transistor) instantly enables or inhibits SCR firing at the delay angle commensurate with the SIG HI command signal.
  • 50/60 Hz Frequency Selection: Operation from 50 or 60 Hz mains may be selected via an onboard jumper.
  • High Current Picket Fence Gate Drive: The transformer-isolated gate drive circuits provide a hard firing initial 15 V open circuit/1.5 A short circuit firing pulse followed by sustaining “back porch” pulses at 7 V open circuit/0.5 A short circuit. The gate pulse burst frequency is 256 times the mains voltage frequency.
  • Power-On Reset: A special circuit prevents unintentional SCR gating upon board power-up.
  • Analog Delay Determinator Circuit: Enerpro’s gate delay determinator circuit is based on an analog PLL circuit and implemented with a proprietary ASIC. This circuit adjusts the gate delay firing angle in negative proportion to the SIG HI delay angle command signal.
  • Plug-In Regulator Boards: Two plug-in regulator boards are available for the FCRO4100. The VRCL1P-1 board provides voltage regulation and current limit functionality. The PTIR-1 board provides voltage regulation and allows the user to program a specific dead time between switching polarity of an 8-SCR bridge rectifier.
  • Simple Control Power Connection: The FCRO4100 derives its control power from the same ac source controlled by the SCRs. An onboard transformer steps down 120, 240, or 480 Vac mains and also provides the phase reference signal for the firing circuit.
  • Board Construction: All circuit boards are assembled at the Enerpro plant in Goleta, California and are manufactured by a UL-approved fabricator from 2.4 mm thick FR4 fire resistant fiberglass epoxy laminate. All boards are conformal coated (MIL-1-46058, Type UR).

SPECIFICATION:

APPLICATIONS:

  • Controlled Reversing Rectifier (Four-Quadrant)
  • Sequence Reversing AC Controller


► Công ty Giải pháp và Công nghệ Đo lường INO, nhà cung cấp các thiết bị đo lường và tự động hóa công nghiệp► Các câu hỏi, thắc mắc, thông tin liên quan đến sản phẩm từ khâu mua sắm, lựa chọn, sử dụng, cài đặt hay thay thế, vui lòng liên hệ với INO team để được hỗ trợ và tư vấn kịp thời.

Web: www.ino.com.vn  |  Mail:info@ino.com.vn

Tel: 028 73000184  |  Hotline: 0947 200 184
Website: http://www.ino.com.vn